Frequently Asked Questions. Single stroke letters are of two types. Final design is then reproduced and sent to the job site or the shop. The exact length of the member is shown by the dimension. 1164 kb/s. Download Engineering Drawing Short Questions And Answers Pdf: FileName.
Question5: What is difference between a plane and a lamina? Q10 – List out the contents of title block and material list. Engineering, drawing has its own grammar in the theory of projections, its idioms in conventional practices, its punctuations. The normal lettering have normal height and width and are used for general. The title block should contain at least the following informations. It is very essential for good lettering in engineering drawing. Vertical or upright freehand gothic lettering. Q6: What are the different multisection views? purposes. Why are sectional views used in drawing? 37,771 Views, In this Engineering Drawing 1st Year Notes Contents :-. The pencil is rotated in finger while drawing a long line in order to get a line of uniform thickness. 1) The knowledge of shape and proportion of each letter. HB and H grade pencils sharpened to a conical point should be used for lettering. This line will be parallel, perpendicular or inclined to the x-y line. Inclined or italic freehand gothic lettering. Where as, mutli view projection is a procedure that can be used to completely describe an object’s dimension or shape using two or more (multi) views that are normally projected at 90 degree to each other or at any other specified angles. Questions & Answers on Drawing Instruments, Sheet Layout & Free-Hand Sketching. one stroke of the pencil. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Q6 – What are the ways of sharpening a pencil for good and accurate work and which type of pencil is more, There are two ways of sharpening a pencil (i) a small piece of sand paper of zero grade, pasted upon a, piece of wood. To convey ideas, shapes, dimension, procedures, for the manufacture or the construction, drawings are used in engineering. The conventional representation of common features are adopted on the drawing to save the. Engineering Drawing Short Questions And ... 6764 kb/s. Q20 – What do you mean by uniformity of letters? Required fields are marked *. Q5 – What are the standard sizes of drawing sheets according to I.S.I. Q9: What are the examples of engineering drawing? Folding marks are made on the sheet to facilitate folding of prints for the purposes of filing and. The art of writing the alphabets without the use of drawing instrument is called freehand lettering. Engineering Drawing Short Questions And Answers Pdf | added by request. Usually hard pencils such as H, 2H etc are used for making the engineering. and which is suitable for drawing, The standard size of sheets according to I.S.I. Engineering Drawing Pdf 1st Year Notes & PPTs – EDP Pdf Notes, JNTUK 1-2 Results 2016 Released (R13,R10,R07,R05) B.Tech Regular/Supply – May 2016, Introduction to Aerospace Engineering Pdf Notes – IAE Notes | Free Lecture Notes download, Conversion of Pictorial View into Orthographic Views, Diameter: The straight distance from a outside curved surface to the opposite outside curved surface through the center point, Radius: The distance between the center point and the outside curved surface is called radius. Q1: What is a circle and its components while considering engineering drawing? The uniformity of lettering means keeping the height, inclination, spacing and strength of letters to be. Each view shows the shape of an object for a particular view direction and collectively the views describe the given object completely. Hard pencils. Q16 – Why the conventional representation of common features are adopted on the drawing? The straightness of edges of the set-square can be checked by drawing a vertical line. Now reverse the T-square and again draw, a horizontal line with working edge. as gothic lettering. medium is 2 times thicker than a thin line. Q11 – What is the necessity of folding a drawing print? The section contains questions and answers on sheet layout, machine types drawing, free hand sketching, drawing tools and their uses. Major components of the circle include, drawing is a starting point of all engineering branches such as Mechanical, Production, Civil, Electrical, Electronics, Computer science, Chemical etc. (iv) Lower case italic freehand gothic lettering. A5: Different classification of axonometric projections are. The process of dimensioning should follow the below guidelines. and H.T. (ii) Lowercase vertical freehand gothic lettering. If there is any difference between the two vertical lines, then working edge is not correct and the line gives twice the error. code. Pictorial view: For this view either oblique projection or perspective projection is used in which the object is oriented behind and projected up on a single plane. There are three distinct thickness of lines used in engineering drawing. Drawing board, T-square, Set Square, Scales, Pencil and sand paper block, Drawing pins or cello-tape. Here’s list of Questions & Answers on Engineering Drawing Subject covering 100+ topics: 1. Note : Please watch the video to know the best way to understand the ppt and its usage before you download the file. 19458. 3) The knowledge of the general composition of letters. The art of writing the alphabets A, B, C,…….Z and numbers such as 1, 2, 3……0 etc. of a section plane? (i) Single stroke vertical freehand gothic lettering. Q5: What are the classification of axonometric projections? Orthographic view: This view consists of two or more separate views of an object which has been taken from different directions, generally at right angles to each other and arranged relative in a definite way to each other. Engineering Drawing Short Questions - Free download as PDF File (.pdf), Text File (.txt) or read online for free. Tags Engineering drawing Engineering drawing notes engineering drawing notes free download engineering drawing pdf Engineering drawing ppt, Your email address will not be published. are generally shown in the, middle by the conventional breaks so as to accommodate their view of whole length on the drawing sheet.